null

The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.

×
click to zoom in

Questions?

  • WARNING: Cancer and Reproductive Harm -

    www.P65Warnings.ca.gov

Paragon 2-piece Rotors Rear Pair 345mm x 24mm (13.58" x 0.94") - BMW M Performance / M Sport (160mm E-brake Drum)

(No reviews yet) Write a Review
$950.00 Per Pair
Application:
M Performance / M Sport (F22/F30/F32)
Part Number:
P2R.014.345.240.20100.01.01.01/02.R
Availability:
In Stock

Product Details

Show Less Show More

Paragon 2-piece Rotors (Rear Pair) - BMW F22/F30/F32 with M Performance / M Sport brakes (160mm Hand brake)

Paragon Performance 2-piece Rotor offers superior braking and cooling efficiency optimized for track and race applications. It features directional ventilation vanes to create suction, turbulence, and guides cool air through the rotor for improved heat dissipation and increased resistance to cracking under harsh track condition.

Made of CM-250 special formulated high carbon alloy cast iron, it allows for an optimal bite, thermal characteristics, high-temperature strength and durability. Rotor rings are heat treated to release stress in the rotor to avoid deformation and vibration then turned by state-of-the-art CBN surface machining to ensure better break-in with new brake pads.

Vibration is reduced as the rotor lateral run-out is kept within 0.03mm and well-balanced: variations are kept within 2 grams. All rotors went through rigorous quality control procedures and inspections to ensure the rotors are fit for their purposes. A slotted rotor improves braking consistency by maintaining a clean contact surface and dissipate heat generated and gases released when the pads come into contact with the rotors. Slotted rotors have a superior advantage over blank rotors in wet or raining conditions by preventing water films to form between the brake pad and rotor surface. Weighing less than most O.E. rotors while maintaining proper thermal capacity, our 2-piece rotors improves overall handling by saving unsprung mass.

 

Aluminum hats are CNC machined from lightweight 6061-T6 aerospace grade aluminum for high strength and durability under extreme track conditions, then black hard coat/hard anodized to increase resistance to wear and corrosion. Mil-spec Type III anodized hats will not discolor under extreme heat, and are harder and more wear/scratch resistant. Unnecessary materials are taken out from the aluminum hats for maximum weight savings while maintaining proper structural integrity. 
*Black hard coat and hard coat anodized hats are the same in terms of performance and durability.

 

  • Direct bolt-on without any modifications and designed to work flawlessly with OEM ABS and brake system while maintaining factory brake bias. Compatible with OEM brake pads or aftermarket pads with the same pad depth (D)

  • Directional ventilation vanes for optimal cooling performance, runs up to 30% cooler than O.E. rotors and increase cooling efficiency by up to 30%

  • 2-piece design

  • Minimizing brake fade & judder during extended sessions

  • Utilizes OEM E-brake by integrating iron sleeve into aluminum hat

  • Weighs 17.73 lbs (8.04 kg)
  • Rotor to hat mounting system: Fixed hat, non-floating (8 bolt)

 

Direct replacement of: OEM BMW part # 34206797605 / 34206797598 

 

Includes:

  • One pair of Paragon Performance 345mm x 24mm (13.58” x 0.94”) 2-piece rotor assemblies with black hard coat/hard anodized 6061-T6 aerospace grade aluminum hats (assembled and ready to install)

  • Detailed installation manual

 

Part # (w/ black hard anodized hat): P2R.014.345.240.20100.01.01.01.R

Part # (w/ hard anodized hat): P2R.014.345.240.20100.01.01.02.R

 

Extra/replacement hardware is available for purchase. We recommend using new hardware when replacing rotors to ensure the rotor ring is attached to the aluminum hat properly. Please refer to our Rotor Assembly Instructions for torque specs and detailed instructions. 

 

Note: Will only fit vehicles with M Performance or M Sport brake packages. Please read the fitment guide below before ordering, and contact us if you have any questions about fitment on your vehicle. 

 

Applications:

  • F22 228i / 228iX / 230i / 230iX with M Performance / S2NHA M Sport/ZTR brakes
  • F22 M235i / M235iX / M240i / M240iX with M Performance / S2NHA M Sport/ZTR / base (M Sport) brakes
  • F22 M235i Racing / M240i Racing
  • F30 320i with M Performance / M Sport/ZTR
  • F30 328i RWD Sedan -07/2014 with M Performance / S2NHA M Sport/ZTR brakes
  • F32 428i RWD Coupe -07/2015 with M Performance / S2NHA M Sport/ZTR brakes

 

If you're unsure of your vehicle's chassis or options, please send us your VIN and we can verify fitment.

Technical Specifications

Show Less Show More

Specifications:

Diameter: 345mm (13.58")

Thickness (new): 24mm (0.94")

Thickness (min.): 22mm (0.87")

Type: 2-piece non-floating

Face Pattern: Slotted

Vented / Solid: Directional ventilated

Number of Vanes: 48

Hat Material: 6061-T6 Aluminum w/ integrated iron sleeve for e-brake

Friction Ring Material: CM-250 high carbon alloy cast iron

Rotor Finish: CBN turned

Weight (per rotor): 17.73 lbs (8.04 kg)

 

Cross Reference:

OEM BMW  34206797605 / 34206797598 

Brembo  09.C396.13 / 09.C400.13

EBC  GD2067R

Centric/Stoptech  120.34145 / 121.34145 / 125.34145 / 126.34145

DBA  2677E

Customer Reviews

0 Reviews Write a Review Show Less Show More

SUBSCRIBE TO PARAGON PERFORMANCE

Be the first to know about new products, sales, collaborations, and special discounts.

to top